חומר המיועד ליצירת חלקים אשר עומדים בתקן UL94 V-0, בעלי איכות גבוהה ועמידות לחום.
ליצור בקלות ובמהירות חלקים פלסטיים קשיחים, עמידים בפני שינוי צורה ופונקציונליים שמתפקדים היטב לאורך זמן בסביבות פנימיות ובסביבות תעשייתיות. רזין FR הוא רזין אשר מכבה את עצמו ואינו מכיל הלוגן, עם דירוגים מצוינים בעמידות בפני בעירה, עשן ורעילות (FST).
✅כלים מותאמים אישית, דיגומים וחלקי חילוף לסביבות תעשייתיות עם טמפרטורות גבוהות או מקורות להבערה
✅חלקים פנימיים במטוסים, רכבים ורכבות עם גימור משטח מצוין
✅רכיבי הגנה פנימיים או רכיבי אלקטרוניקה לצרכים רפואיים וצרכניים
| Category | Result | Method | Notes |
|---|---|---|---|
| Flammability (UL 94) | V-0 (3 mm) | UL 94 | Highest flammability rating, extinguishes in under 10 seconds without flaming drips |
| V-1 (2.5 mm) | UL 94 | Acceptable flammability rating, extinguishes within 30 seconds with flaming drips | |
| HB (1.5 mm) | UL 94 | Slow burn rate when tested horizontally | |
| FAR 25.853 Appendix F | 12 seconds – Pass (2.5 mm) | FAR 25.853 Appendix F | Vertical burn test passes the 12-second requirement |
| Smoke Generation (ASTM E662) | Ds @ 1.5 min (3 mm) = 19.5 | ASTM E662 | Smoke density at 1.5 minutes |
| Ds @ 4 min (3 mm) = 285 | ASTM E662 | Smoke density at 4 minutes | |
| Ds @ 1.5 min (5 mm) = 5 | ASTM E662 | Smoke density at 1.5 minutes (5 mm thickness) | |
| Ds @ 4 min (5 mm) = 114 | ASTM E662 | Smoke density at 4 minutes (5 mm thickness) | |
| Gas Toxicity | CO (Carbon Monoxide) = 56 PPM | BSS 7239 | Carbon monoxide levels below 100 PPM are acceptable |
| HCN (Hydrogen Cyanide) = 7 PPM | BSS 7239 | Hydrogen cyanide level is low, but toxic | |
| SO2 (Sulfur Dioxide) = <1 PPM | BSS 7239 | No significant presence of sulfur dioxide | |
| HCl (Hydrochloric Acid) = <1 PPM | BSS 7239 | No significant presence of hydrochloric acid | |
| HF (Hydrofluoric Acid) = <1 PPM | BSS 7239 | No significant presence of hydrofluoric acid | |
| NOx (Nitrogen Oxides) = <1 PPM | BSS 7239 | No significant presence of nitrogen oxides |
נתונים טכנים:
| Category | Property | Metric (3.5) | Imperial (3.5) | Method |
|---|---|---|---|---|
| Post-Curing Conditions | Post-Cured for 60 min at 70°C | Post-Cured for 60 min at 158°F | ||
| Post-Cured for 120 min at 80°C | Post-Cured for 120 min at 176°F | |||
| Mechanical Properties | Ultimate Tensile Strength | 24 MPa | 3560 psi | ASTM D638-14 |
| 38 MPa | 5990 psi | ASTM D638-14 | ||
| 41 MPa | 5990 psi | ASTM D638-14 | ||
| Tensile Modulus | 1.8 GPa | 263 ksi | ASTM D638-14 | |
| 2.9 GPa | 430 ksi | ASTM D638-14 | ||
| 3.1 GPa | 446 ksi | ASTM D638-14 | ||
| Elongation at Break | 20% | 20% | ASTM D638-14 | |
| 9.4% | 9.40% | ASTM D638-14 | ||
| 7.1% | 7.10% | ASTM D638-14 | ||
| Flexural Properties | Flexural Strength | 36 MPa | 5280 psi | ASTM D790-15 |
| 72 MPa | 10500 psi | ASTM D790-15 | ||
| 75 MPa | 10900 psi | ASTM D790-15 | ||
| Flexural Modulus | 1.3 GPa | 188 ksi | ASTM D790-15 | |
| 2.7 GPa | 392 ksi | ASTM D790-15 | ||
| 2.7 GPa | 401 ksi | ASTM D790-15 | ||
| Impact Properties | Notched Izod | 19 J/m | 0.36 ft-lb/in | ASTM D256-10 |
| 22 J/m | 0.41 ft-lb/in | ASTM D256-10 | ||
| 0.42 ft-lb/in | ASTM D256-10 | |||
| Unnotched Izod | 227 J/m | 4.26 ft-lb/in | ASTM D4812-11 | |
| 241 J/m | 4.51 ft-lb/in | ASTM D4812-11 | ||
| 257 J/m | 4.82 ft-lb/in | ASTM D4812-11 | ||
| Fracture Properties | Maximum Stress Intensity Factor (Kmax) | 1.05 MPa · m¹/₂ | 956 psi · in¹/₂ | ISO 20795-1:2013(E), Section 8.6 |
| Work of Fracture (Wf) | 311 J/m² | 21 ft-lb/ft² | ISO 20795-1:2013(E), Section 8.6 | |
| Thermal Properties | Heat Deflection Temp. @ 1.8 MPa | 45°C | 113°F | ASTM D648-16 |
| 71°C | 160°F | ASTM D648-16 | ||
| Heat Deflection Temp. @ 0.45 MPa | 55°C | 131°F | ASTM D648-16 | |
| 94°C | 201°F | ASTM D648-16 | ||
| Coefficient of Thermal Expansion (20°-80°C) | 98.6 μm/m/°C | 37.8 μin/in/°F | ASTM E813-13 | |
| Glass Transition Temperature (Tg) | 101°C | 214°F | Peak of tan delta, Heating Rate: 3°C/min | |
| 130°C | 266°F | |||
| 144°C | 291°F | |||
| General Properties | Hardness | Green: 74D, Post-Cured: 80D | ASTM D2240 | |
| Bulk Density | 1.25 g/cm³ | ASTM D792-20 | ||
| Viscosity (25°C) | 4500 – 5000 cP | |||
| Color | Light grey | |||
| Electrical Properties | Dielectric Strength | 15.1 kV/mm | ASTM D149 | |
| Dielectric Constant | 3.83 | ASTM D150, 0.5 MHz | ||
| 3.82 | ASTM D150, 1.0 MHz | |||
| Dissipation Factor | 0.024 | ASTM D150, 0.5 MHz | ||
| 0.025 | ASTM D150, 1 MHz | |||
| Volume Resistivity | 2.1 x 10¹⁵ ohm-cm | ASTM D257 | ||
| Outgassing | Total Mass Loss and Collected Volatile Condensable Materials | Pass | ASTM E595 | |
| Total Mass Loss (TML) | 0.87% | |||
| Collected Volatile Condensable Material (CVCM) | <0.01% | |||
| Water Vapor Recovered (WVR) | 0.2% |
